Remotec ZTS-110 V3.12 Bedienungsanleitung

ZTS-110Z-ThermostatUSER MANUALFirmware Version: 2.06

9Jumper Settings for ELECTH-HPUMP and HE-HGThere are 6 jumpered pins on the thermostat circuit board that identify whether your system is:- Gas or ele

10Setup and OperationsProduct OverviewFigure 8. ZTS-110Description of Function KeysEvent modeDayTimeProgram mode Fan modeInclusion indication Battery

11Activate/Deactivate Easy ModeThe ZTS-110 is default with Easy mode, below illustrates the functions of Easy mode:- Active functions: Change Mode, ch

12Note:If you deactivated the Easy mode, please refer to Setting Mode for the temperature scale selection.Setting Mode (Set Day, Clock, 12/24 hour, F/

13If you deactivated the Easy mode, you can continue to set up Day, Clock, 12/24 hour, F/C, Swing and Differential. Refer to below for steps:LCD indic

14LCD indicationStep Procedure / DescriptionPress "Prog" key once to confirm the setting and it will go to minutes setting.Minutes will keep

15Note: Explanations of Swing and Differential set pointHEAT mode: thermostat controls the temperature according to the following diagramo o o Examp

16COOL Mode: thermostat controls the temperature according to the following diagramo o Example for Cooling: (Set point = 80 F, Swing = 1 F)o o =>

Change ModeNote: In Heat mode =>it displays "HEAT" if ELECTH is selected during jumper setting.=> it displays "HEAT PUMP" if

18Change Fan ModeSelect Program ModeLCD indicationStep Procedure / DescriptionPress "Prog" key once to select PROG mode:PROG ON -> OVERRI

Table of ContentsIntroduction 2Features list 3Glossary 4Physical Installation and Wiring 5Installation Location 6 6Wiring 7Jumper Settings for ELEC

Override/Permanent OverrideNote: Override/Permanent Override is only available in HEAT, COOL or AUTO mode.LCD indicationStep Procedure / DescriptionPr

20Setting ScheduleBelow are the recommended settings for different schedule scenarios:Pre-defined Schedule (disabled by default):ZTS-110 Easy mode set

LCD indicationStep Procedure / DescriptionPress and hold "Prog" key for 2 seconds to entry the setting schedule mode.Press Up/Down key to se

LCD indicationStep Procedure / DescriptionPress and hold "UP" and "DOWN" key for 2 seconds to disable / enable event during the ti

Battery Low IndicationDefrost IndicationOut of Temperature Range Indication23LCD indicationProcedure / DescriptionZTS-110 thermostat will detect the b

24Advanced Recovery IndicationLCD indicationProcedure / DescriptionThe Advanced Recovery feature allows heating and cooling systems to gradually recov

25Filter CounterShort Cycle Start Up ProtectionTo protect the compressor / Heat pump, those outputs forced off until 3minutes count down finished. Tho

26Energy Saving ModeUser can enable/disable energy saving mode by using Z-Wave BASIC set command only. (you may refer to the Z-Wave primary controller

27Important:Please note the below scenarios for power applying because it will affect the battery life if the steps are not correct (this is also ment

Check FLiRS / Always Listening mode in ZTS-110Z-Wave Add (Include) / Delete (Exclude) into/from Z-Wave networkAdd (Include) ZTS-110 to Gateway / Contr

ZTS-110 Z-ThermostatIntroductionZTS-110 Z-Thermostat (Figure 1) is a Z-Wave enabled programmable thermostat that allows you to control your room tempe

Note:- It is recommended to perform the Delete/Exclude procedure before doing Add/Include. This is to make sure the ZTS-110 is not in any other Z-Wave

30Delete (Exclude) ZTS-110 from Gateway / Controller Z-Wave networkSupport Association Groups (Association Command Class)ZTS-110 supports 3 associatio

31Association group_3: (Auto report)- Association group_3 is used to report status change to gateway. (Only gateway or controller can be assigned in t

32Z-Wave Configuration ParametersDifferent user has different preferred settings of their thermostat, you may use the below configuration parameters t

0 (0x00) = Disable1 (0x01) = Enable, default8 (0x08)Easy mode0 (0x00) = 24 hours1 (0x01) = 12 hours (am / pm), default9 (0x09)Value(X): 0 (0x00), 3 (0

0 (0x00) = disable AUTO report function. (by time interval)AUTO report timer:1 (0x01) = 0.5 hr2 (0x02) = 1.0 hr, (default)3 (0x0

Example for sensor temperature calibration: o o reading temperature (77 F) + (-2 F)If using decimal input If using hexadecimal inputParameter no. =

36Frequently Asked QuestionsQ Why won't my ZTS-110 work with the Z-Wave devices I purchased from another country?A Due to different countries reg

37Technical SpecificationsModel no.BW8031US (ZTS-110US)BW8031AU (ZTS-110AU)BW8031EU (ZTS-110EU) RF frequency908.4MHz (US) (ZTS-110US)921.4MHz (AU) (ZT

38Checking AccessoriesAfter opening the cover of the packaging box, check that the following accessories are included. - ZTS-110: Z-Thermostat - AA ba

Features ListHVAC System Type Compatible: - Standard (gas/electric) or Heat PumpMultistage System Compatible: - Standard HVAC Systems: 2 stage heating

Printed in ChinaF820-8031-000439FCC NoticeThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1

GlossaryDevices and nodes are all terms to describe an individual Z-Wave device. These are all interchangeable when setting up your Z-Wave network.Dev

Physical Installation and WiringRead following scenarios carefully before you start as it matters to the battery life under Z-Wave operation:ZTS-110 c

6Installation LocationThe Thermostat is restricted to be used in indoor only. It should be mounted on an inner wall about 1.5m (5ft) above the floor a

7Wiring- Be sure the operation mode is OFF and Fan selection is Fan Auto- Wire the proper cables at the terminal block according to the circ

Figure 5. Heat pump HVAC system wiringFigure 6. Non-heat pump 2-wires system wiringFigure 7.Heat pump 2-wires system wiringThermostat should be powere